Eagle Rotorcraft Simulations Forums
>
Eagle Rotorcraft Simulations
>
Support 
>
Bell 206 Contact points
>
Bell 206 Contact points
|
Bell 206 Contact points
» Troubles with FS9 |
|
08-12-2011, 12:20 PM
Post: #1
|
||||
|
||||
|
Bell 206 Contact points
Hello!
I downloaded the low skid/floats Bell 206 model and it looks pretty good ^^ ... but i have a problem with it. Everytime i load the Bell 206 ls the helo crashes into ground, or in other words the flightsim shows "Crash" and if i don't press "Y" early, it goes on and on. Well If i pull it some feet over the ground and land the Bell normaly all is okey. It's only then i load it out of the Aircraft menu. Could it be possible, that this bug is caused by the contact points? Best regards, Elmar |
||||
|
|
08-12-2011, 12:48 PM
Post: #2
|
||||
|
||||
|
RE: Bell 206 Contact points
Elmar,
You have to specify for which model of the 206 is causing the issue. Is this for the float or low skid Bell 206? ![[Image: ers_george_sig1.jpg]](http://i107.photobucket.com/albums/m305/euroastar350/Avatars%20and%20Sigs/ers_george_sig1.jpg) http://www.facebook.com/euroastarthreefifty http://www.flickr.com/photos/euroastar350/ I'm with the FAA and I'm here to help you.....................Now gimme a hug! |
||||
|
|
|
08-12-2011, 01:12 PM
Post: #3
|
||||
|
||||
RE: Bell 206 Contact points
(08-12-2011 12:48 PM)euroastar350 Wrote: Elmar, The low skid model ... i didn't test the floats one yet. |
||||
|
|
|
08-12-2011, 01:17 PM
Post: #4
|
||||
|
||||
|
RE: Bell 206 Contact points
Either myself or Brandon will look into the issue and post any corrections. Thanks for the feedback.
http://www.facebook.com/euroastarthreefifty http://www.flickr.com/photos/euroastar350/ I'm with the FAA and I'm here to help you.....................Now gimme a hug! |
||||
|
|
|
01-20-2013, 03:52 AM
Post: #5
|
||||
|
||||
|
RE: Bell 206 Contact points
HI,
I've the same problem with the float : they are not matching and the helicopter don't float !! |
||||
|
|
|
01-20-2013, 08:36 AM
Post: #6
|
||||
|
||||
RE: Bell 206 Contact points
![[Image: ers_brandon_sig_mar2012.png]](http://www.eaglerotorcraftsimulations.com/images/signatures/ers_brandon_sig_mar2012.png) Intel Xeon E5-1620 v2 @ 3.7GHz | 8GB DDR3 RAM | NVIDIA GTX 760 | Windows 8.1 64 bit | FSX Acceleration/SP2 (DX10 Mode) |
||||
|
|
02-03-2013, 07:15 PM
Post: #7
|
||||
|
||||
RE: Bell 206 Contact points
(08-12-2011 01:12 PM)Elmar Wrote:(08-12-2011 12:48 PM)euroastar350 Wrote: Elmar, This may not be the "best" solution - however - In the Aircraft.cfg [Contact_points] I changed the "class" from 3 = skid to 4 and the "float version" now floats. Backup cfg file first!! |
||||
|
|
|
« Next Oldest | Next Newest »
|
User(s) browsing this thread: 1 Guest(s)
